EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP Manual de Instruções Página 53
- Página / 64
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Instruction Manual CyberScan pH 1100/ 2100
53
10.5.6 Communication setup mode P4.4
Use this program to set parameters of serial communication.
1. Enter meter setup mode as described in steps 1-4 in Section
10.5.1 Entering meter setup mode (page 50).
2. Use ∆/MI key to scroll to program Tx/Rx Parameter: P4.4.
See Figure 175.
3. Press ENTER to enter program Tx/Rx Parameter: P4.4.
4. Press >/CALkey to toggle between Baud Rate 4800, 9600 and
19200. The selection will flash. See Figure 176. Press ENTER
to confirm selection and go to the next setup screen.
5. Press >/CALkey to toggle between Stop Bit One and Two.
The selection will flash. See Figure 177. Press ENTER to
confirm selection and go to the next setup screen.
6. Press >/CALkey to toggle between Parity Bit None, Odd and
Even. The selection will flash. See Figure 178.
7. Press ENTER to confirm selection and return to the setup mode.
Press ∆/MI key to continue to the next setup program, or press
∇/MR to go to the previous program. Press EXIT to return to
measurement mode.
10.5.7 Data transfer setup mode P4.5
1. This program lets you select what data is sent to your printer or
computer.
2. Enter meter setup mode as described in steps 1-4 in Section
10.5.1Entering meter setup mode (page 50).
3. Use ∆/MI key to scroll to program Data Transfer: P4.5. See
Figure 179.
4. Press ENTER to enter program Data Transfer: P4.5.
5. Press >/CALkey to toggle between Data send to printer Current
and Memory. .The selection will flash.
See Figure 180.
6. Press ENTER to confirm selection and return to the setup mode.
Press ∆/MI key to continue to the next setup program, or press
∇/MR to go to the previous program. Press EXIT to return to
measurement mode.
Stop Bit: One Two
Baud Rate
4800 9600 19200
Tx/Rx Parameter:P4.4
Press ENT. to Select
Parity Bit:
None Odd Even
Figure 175
Figure 176
Figure 177
Figure 178
Data send to printer
Current Memory
Data Transfer :P4.5
Press ENT. to Select
Figure 179
Figure 180
- Instruction Manual 1
- PREFACE 3
- TABLE OF CONTENTS 4
- 1 INTRODUCTION 6
- Figure 1: Membrane Keypad 7
- 1.3 Rear Panel 8
- 1.4 Electrode Holder 9
- 2 STARTING UP 10
- Attention: 10
- Selectable buffer sets: 11
- Figure 13 12
- Figure 14 12
- Figure 15 12
- . See Figure 17. This 13
- Cal Done 13
- NOTE: 14
- . See Figure 26. Press 15
- 3.2 pH measurement 16
- Figure 35 17
- Figure 36 17
- 18
- pH/Temp mV Ion 19
- 5.1 Ion calibration 20
- Ion Conc: 1.0ppm 21
- 3 Point Cal Done 21
- Aver. Slope = 49.2mV 21
- Sys Updating. . 21
- 5.3 Ion measurement 22
- 5.695pH 25.3 C ATC 23
- Data Log. . . . Loc: 9 23
- 6.2 Memory recall 24
- 7.546pH 25.4 C ATC 25
- 9.1 Temperature Calibration 26
- 10.1 Setup mode overview 27
- Tx/Rx Parameter: P4.4 29
- Press ENT. to Select 29
- USA NST Bf1 Bf2 Cust 30
- Select & Press ENTER 30
- Figure 83 31
- Figure 84 31
- Figure 85 31
- Figure 86 31
- Key In Low Alarm 32
- Key In High Alarm 32
- Figure 91 33
- Figure 92 33
- Figure 93 33
- Figure 94 34
- Figure 95 34
- Figure 96 34
- Figure 101 35
- = 0.2 mV 35
- Figure 105 36
- Figure 106 36
- Figure 107 36
- Figure 108 36
- Figure 109 37
- Figure 110 37
- Figure 111 37
- Figure 112 38
- Figure 113 38
- Figure 1 38
- Figure 115 38
- Figure 116 39
- Figure 117 39
- Figure 118 39
- Figure 119 40
- Figure 120 40
- Figure 121 40
- Figure 124 41
- = 3.2 mV 41
- Figure 125 42
- Figure 126 42
- Figure 127 42
- Figure 128 42
- Figure 132 43
- Figure 133 43
- Figure 134 44
- Figure 135 44
- Figure 136 44
- Figure 137 44
- Figure 138 45
- Figure 139 45
- Figure 140 45
- Figure 141 46
- Figure 142 46
- Figure 143 46
- Resolution: High Low 47
- Ion Mode Setup : P3.4 47
- Figure 155 49
- Figure 156 49
- Figure 157 49
- Figure 158 49
- Figure 167 51
- Figure 168 51
- Figure 169 51
- Memory Recall Mode 52
- Auto Manual 52
- MemRecall Setup:P4.3 52
- Data send to printer 53
- Current Memory 53
- Data Transfer :P4.5 53
- Figure 185 54
- Figure 186 54
- Figure 187 54
- Figure 184 54
- 11 ELECTRODE CARE 55
- 12 RS 232 COMMUNICATION 56
- 13 ADDITIONAL INFORMATION 57
- Offset of temp. probe 59
- Temperature 60
- 17 ACCESSORIES 61
- 18 WARRANTY 62
Manuais e produtos relacionados com Medição, teste e controlo EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP
Medição, teste e controlo EUTECH INSTRUMENTS ALPHA PH1000 PHORP CONTROLLERTRANSMITTER Manual de Instruções
(40 páginas)
(40 páginas)
(4 páginas)
Medição, teste e controlo EUTECH INSTRUMENTS ALPHA PH1000 PHORP CONTROLLERTRANSMITTER Manual do Utilizador
(20 páginas)
(20 páginas)
Medição, teste e controlo EUTECH INSTRUMENTS ALPHA CON 500 2-WIRE TRANSMITTER Instruções de Operação
(34 páginas)
(34 páginas)
Medição, teste e controlo EUTECH INSTRUMENTS ECOSCAN TEMP JKT PORTABLE METER Manual de Instruções
(20 páginas)
(20 páginas)
Medição, teste e controlo EUTECH INSTRUMENTS ALPHA CON 100 CONDUCTIVITY CONTROLLERTRANSMITTER Manual de Instruções
(34 páginas)
(34 páginas)
Medição, teste e controlo EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER Manual de Instruções
(24 páginas)
(24 páginas)
Medição, teste e controlo EUTECH INSTRUMENTS ALPHA PH1000 PHORP CONTROLLERTRANSMITTER Manual de Instruções
(42 páginas)
(42 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais