EUTECH INSTRUMENTS CYBERCOMM 5000 FOR CYBERSCAN 5000 Manual de Instruções Página 150
- Página / 182
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Instruction Manual CyberScan PC5500/ 5000
145
To “standardize” your Conductivity Probe in the Basic Level of
Operation
At the Basic Procedural level the only setup options that you can
access are the Cell Constant, the Print Interval and the number of
Significant Digits. If you need to change any other parameter such as
reference temperature or temperature coefficient you will need to set
the Procedural Level to Advanced in the System setup screen. Any
values previously saved in the Conductivity setup screen at the
Advanced Procedural Level will become the default values for the
basic Procedural Level.
1. Access the Conductivity Setup screen and verify the value for the
nominal cell constant of the probe.
2. Touch std on the Conductivity Measure screen to access the
Conductivity Standardization screen.
3. Immerse the conductivity and ATC probes in the standard with a
known conductivity value and stir.
4. Touch clear to delete previous standardization values.
5. Touch std to access the standardization mode again.
6. Use the keypad on the display screen to enter the value of the
known conductivity standard.
7. Touch enter on the keypad to accept this conductivity standard
and return to the conductivity measure screen.
- Instruction Manual 1
- PREFACE 3
- TABLE OF CONTENTS 4
- 1 INTRODUCTION 6
- 2 UNPACKING THE METER 7
- 3 GETTING STARTED 8
- Back Panel of PC 5500/ 5000 9
- 11:11 am 15
- System Setup 21
- Language 24
- Current MM/DD/YY 26
- Current 12HR 29
- Current 24HR 29
- Beeper Status 30
- Procedural Level 32
- Print Configuration 34
- Baud Rate 36
- Number of Bits 37
- Stop Bits 38
- Current PARITY 39
- Operator 40
- Display Contrast 42
- Reset to Factory Defaults 45
- 6 pH SETUP 46
- Manual ID# 49
- Sequential ID# 51
- and then touch to accept 53
- 1.78 3.65 55
- Current RECOGNITION 57
- Current MODE 58
- Current CRITERIA 59
- Current DEFAULT 61
- Current ISO POINT 63
- Current LIMITS 65
- Current INTERVAL 69
- touch to accept 73
- Example of X.X resolution 74
- Example of X.XX resolution 74
- Example of X.XXX resolution 74
- Stored Data 77
- 7 mV SETUP 81
- Example of X resolution 87
- Ion Setup (channel 1) 88
- Ion Method 91
- Select Ion 93
- Measurement Units 93
- 8.5 Set Significant Digits 97
- 9 CONDUCTIVITY SETUP 99
- E U T E C H 100
- INSTRUMENTS 100
- Conductivity Units 103
- Cond Cell Constant 104
- Cond Reference Temp 106
- Cond Temperature Coeff 108
- 0.00%/°C 108
- Replatinize 110
- touch to accept 114
- 4 7 10 116
- Standardize 118
- 11 mV OPERATION 124
- Measure - Ion 126
- Standardize - Ion 128
- 12.2 Incremental Methods 134
- 12.3 Known Addition Method 136
- Known Addition Result 137
- 13 CONDUCTIVITY OPERATION 146
- Standardize - Conductivity 148
- Measure - Conductivity 148
- 14 CLEANING 153
- 15 TROUBLE SHOOTING 154
- 16 COMPLIANCE 155
- 17 APPENDIX 156
- E* - (pH) 162
- E* ± (log c) 165
- (V +V )10 - V 167
- ( ) 168
- megohmcm 170
- 18 METER SPECIFICATIONS 174
- 19 ACCESSORIES 176
- 20 WARRANTY 180
Manuais e produtos relacionados com Software EUTECH INSTRUMENTS CYBERCOMM 5000 FOR CYBERSCAN 5000
(12 páginas)Atec Agilent-83491A-92A podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Ekwipunek Atec Agilent-83491A-92A.
Dostarczamy 1 pdf podręczników Atec Agilent-83491A-92A do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentários a estes Manuais